Tiano-MSP430 based TouchScreen Piano

Touchscreens..huh.. They are all around us..Phones ,tablets, phablets and now even laptops. Most of them have a capacitive touchscreen where the change in capacitance at a point is used to sense it and then perform the corresponding action. Capacitive ones are multi point sensing. They sense more than 2 points and hence we get those pinch to zoom features etc.

On the other hand , almost archaic version on touchscreen is the resistive version. That are pretty easy to interface with almost any microcontroller with an ADC. In this project i did over the weekend i tried to interface a touchscreen ( resistive one..) ,available at mobile repair shops in Delhi with a MSP430G2553 (Although MSP430G2231 would also do)  to make a piano.

Touchscreen setup

Pre-requisites: The touchscreen may not be easier to get. I got mine from a mobile repair shop in LR. It is a 4-wire Touchscreen, pretty common with horribly thin contacts that took a lot of patience to solder.There is a lot of literature available on Touchscreens on the internet. I found two app notes that were best. First one from Atmel , that explained the working of the touchsreen in a pretty clear way and one from TI that some what helped in the software part.

You must read the atmel one ( atleast the first few pgs to get how it works). Its essentially a resistive voltage divider. The value of the touch point is determined by the ADC value read.

formula

From the illustration above(borrowed from TI App Note). One can easily see how the co-ordinates are read. In order to find out, what wire on your touch sreen corresponds to X and Y meshes. You can use a multi-meter first to measure the resistance between pins ,usually the alternate pins belong to same axes. in my case it was X-,Y-,X+,Y+  then to differentiate between x and y , one probable method will be to power the touchscreen i.e. giving the drive voltage and then find out the voltage at any other terminal w.r.t. ground and see whether is changing horizontally or vertically in your reference plane.

CAUTION: Be careful about the current while powering the touchscreen externally!

After this coding part is pretty simple. For the algo refer to page no.7 on the TI App Note. If you plan to run your end application on a battery and you have hard-coded the co-ordinates and the Vdrive is sourced externally i suggest that you sample the Vdrive as well . If you are using  microcontroller pins to supply Vdrive then this can be neglected.

I have a desire to learn to play music but unfortunately due to my low patience levels , i have failed to keep up. :D

So, i made this Piano using the MSP430 Launchpad and a touchscreen along with a speaker. The code algo is pretty same as TI App Note Suggests and i encourage the reader to code it himself . Any difficulties can be discussed. It uses the tone library i posted earlier to generate the solfeggio.

Here is the shaky and horrible video i made:

Cheers! :D

About these ads

7 thoughts on “Tiano-MSP430 based TouchScreen Piano

  1. Pingback: MSP430 touchscreen piano

  2. Pingback: MSP430 touchscreen piano | Froppa.com

  3. Pingback: MSP430 touchscreen piano | Blog of MPRosa

  4. Pingback: MSP430 touchscreen piano | Daily IT News on IT BlogIT Blog

  5. Pingback: MSP430 touchscreen piano - RaspberryPiBoards

  6. Pingback: rndm(mod) » MSP430 touchscreen piano

  7. Pingback: MSP430 touchscreen piano | Make, Electronics projects, electronic Circuits, DIY projects, Microcontroller Projects - makeelectronic.com

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s